ASTM A860 EPUB
ASTM A Specification for fittings used in high pressure gas and oil transmission and distribution system. This standard is issued under the fixed designation A/AM; the number 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel. ASTM A/AM Direct No.: + Fax No.: + Email: [email protected] Board No.: +
|Published (Last):||3 April 2010|
|PDF File Size:||10.48 Mb|
|ePub File Size:||18.27 Mb|
|Price:||Free* [*Free Regsitration Required]|
The values stated in each system are not exact astm a860 therefore, each system must be used independently of astm a860 other. JIS G Carbon steel pipes for pressure service. These fittings are for use in. JIS G Arc welded carbon steel pipes. JIS G Carbon steel pipes for ordinary piping. It is informational only and not an official astm a860 of the standard; the full text of the standard itself must be referred to for its use and application.
Historical Version s – view previous versions of standard. Starting materials shall consist of plate, sheet, forgings, forging quality bar, and seamless asmt fusion-welded tubular products with filler metal added.
The nickel content of the deposited weld metal shall not exceed 1. Materials shall be heat treated by normalizing, quenching, and tempering or stress relieving.
The chemical composition thus determined. JIS G Carbon astm a860 pipes for astm a860 temperature service.
Butt-welding fittings differing from these. Wrought austenitic and austenitic-ferritic duplex astm a860 steels without specific inspection requirements BS EN Butt-welding pipe fittings Part 4: These fittings are for use in high astm a860 pressure gas and oil transmission and distribution system. Fittings shall subsequently be heat treat edby atmquenchingand. The material for fittings shall be fully killed fine — grain material made by a.
ASTM does not give any warranty express or astm a860 or make any representation that the astm a860 of this abstract are accurate, complete or up to date. Within the text, the SI units are shown in brackets.
All values are Maximum unless A range is stated. Research astn only,Commercial use is prohibited. JIS G Stainless steel pipes.
JIS G Steel pipes for low temperature service. Section V, Nondestructive Examination. Xstm astm a860 analysis shall be performed on deposited weld metal for each heat of filler astm a860 orfor submerged arc weldingeach heat of filler metal s860 batch of flux the weld metal shall be deposited in accordance astm a860 the qualified weld procedure.
Work Item s – proposed revisions of this standard. These fittings are for use in high-pressure gas and oil transmission and distribution systems. JIS G Carbon steel pipes for high pressure service.
This abstract is a brief summary of the referenced standard. If you want to use it astm a860 can buy from following link: How can I help you?
ASTM A860 Grade WPHY 65 Buttweld Pipe Fittings
There sults shall conform to Table 1 for either. Standard Specimen, Size Specimen.
A chemical analysis shall be performed astm a860 deposited weld metal for. DIN Medium-weight threaded steel tubes.
One or more of astm a860 supplementary requirements may be specified in the order. These fittings are for use astm a860 high-pressure gas and oil transmission and distribution systems. One or more of the supplementary requirements may be specified in the order.
And over, Sizes tested Section;min, specimen, thickness [7. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.
astm a860 Materials and Manufacture … Research use only,Commercial use is prohibited. After the removal of any cracksthe tees shall be re- examined by the removal of any Acceptable tees shall astm a860 marked with the symbol PT or MTas astm a860to indicate compliance. A refers to the high yield strength of the fittings. Link to Active This link will always route to the current Active version of the standard. The nickel content of the deposited weld metal. Specimens shall conform to required values of chemical composition and mechanical properties, namely: NDE personal shall be.
Internal and external surface shall be examined when size permits permits accessibility.
This specification covers wrought high-strength low-alloy butt-welding steel fittings of seamless and electric fusion-welded construction for applications in astm a860 gas and oil transmission and distribution systems.